The article author is making a number of great annotation on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround in general in the article in the next paragraphs.
Installing a bath tub isn't precisely brain surgery, but it does require solid plumbing, woodworking, as well as often, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably difficult job. If the old tub is easily obtainable, the task can relocate immediately; if you need to open up a wall surface to remove the old bathtub as well as position the brand-new bathtub, the job is much harder. In either instance, the task is within a home handyman's skills, although you will require a helper to vacate the old bathtub and set in the brand-new one. Make sure you have certified on your own for the job as well as fit attempting it. Rather than hiring a specialist to take over a halfway-completed task, it is much better to think about employing one before you begin. Opportunities are you may need an expert plumber to make tube links.
This post will certainly help you set up a brand-new bath tub in your washroom if you have actually already bought a brand-new bathtub and also do not need to change the arrangement of your previous water system pipelines.
Your tools and also material list need to comprise the following:
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you must do is disconnect the water. After doing so, activate the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing taps can be rather problematic due to the restricted access that is frequently the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the faucets. Have a cloth prepared for the remaining water that will certainly come from the pipes. Once the supply pipelines have actually been removed, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing compound.
Before going on to fit the new taps, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap and the other end provides a connection to the current supply pipes.
If you require to fit a monobloc, then you will call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the tap in the installing hole in the bath/basin guaranteeing that the washing machines remain in area in between the faucet and the sink. Safeguard the faucet in place with the producer given backnut. Once the faucet is securely in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The former kind must be linked to the faucet finishes first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Tub
Using both wooden boards under its feet, place the bathtub in the needed setting. The wood boards are helpful in uniformly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 small points.
The next goal is to guarantee that the bath tub is leveled all round. This can be accomplished by checking the spirit level and changing the feet on the bathtub till the level checks out level.
To install faucets, fit all-time low of the outermost versatile tap connector to the proper supply pipeline by making a compression join; after that do the exact same for the various other tap.
Turn on the water system and examine all joints as well as new pipework for leakages and tighten them if essential. Fill up the bath tub as well as additionally inspect the overflow outlet as well as the typical electrical outlet for leaks.
Lastly, deal with the bathroom paneling as described in the producer's instruction manual. Tiling and securing around the bath tub ought to wait till the bathtub has been made use of at least once as this will resolve it into its final position.
Getting ready for the Setup
To start with, the supporting structure supplied with the bath must be fitted (if called for) according to the producer's directions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is important to ensure that if the tap includes a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets system to avoid strain on the tub.
Fit the flexible faucet adapters to the bottom of both faucets utilizing 2 nuts and also olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bath. Utilize the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make certain you use every one of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be fitted in its last placement.
Tiling Around the Bath tub
In the area where the bath meets the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the installation can move sufficient to break an inflexible seal, causing the water to permeate the wall surface between the bath and also the tiling, bring about problems with dampness and possible leakages to the ceiling below.
You can choose from a variety of coloured sealants to assimilate your fixtures as well as fittings. They are sold in tubes as well as cartridges, and also can securing gaps approximately a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the bath tub with water before securing, to enable the activity experienced when the bathtub is in use. The sealer can crack rather early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily offered on the market. It is advisable to fit the tiles using water-resistant or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like reading up on Installing A Bathtub? Create feedback down below. We'd be delighted to see your thoughts about this blog post. Hoping that you visit us again in the near future. So long as you liked our blog entry please make sure you remember to pass it around. I praise you for your time. Don't forget to check up our site back soon.
Fast and effective, call!